main logo

Can To Uart

I 10 migliori prodotti di aprile 2025
Ultimo aggiornamento: 28 aprile 2025
Waveshare
Waveshare
Waveshare TTL UART To CAN Mini Module, With TTL And CAN Conversion Protocol, Supports Bi-Directional Transmitting And Receiving, Multiple Operating Modes
Spedizione gratuita
star

99

QUALITÀ MASSIMA

VEDI SU AMAZON
Amazon.it
#1 VINCITORE

  • Onboard high-performance MCU and CAN transceiver chip, small in size, low power and easy to integrate. Built in TTL and CAN conversion protocol algorithm, enabling data conversion communication between TTL and CAN via simple configuration
  • Supports 3.3V operating voltage on TTL interface, supports both CAN 2.0A (standard frame) and CAN 2.0B (extended frame) on CAN interface. Supports 14 sets of configurable filters, can only receive CAN bus data in specific range and type via configuration
  • Supports 4 operating modes: transparent conversion, transparent with identifiers conversion, format conversion, and Modbus RTU protocol conversion. Supports offline detection and automatic recovery functions
  • UART communication baudrate: 1200bps～460800bps. CAN communication baudrate: 10kbps~1000kbps, configurable. Up to 1000 frames CAN buffer for buffering transmission data to prevent data loss
  • Supports high-speed conversion, the CAN transmission speed can reach up to 1270 extended frames per second with the UART at 115200bps and CAN at 250kbps (close to the theoretical max value of 1309), and can exceed 5000 extended frames per second with the UART at 460800bps and CAN at 1000kbps. Supports device firmware upgrade via TTL, more convenient for firmware update and function customization
  • 16,99 € SU AMAZON
HiLetgo
HiLetgo
HiLetgo 2pcs CP2102 MICRO USB to UART TTL Convert Module 6Pin Serial Converter Adapter UART STC Replace FT232 for Arduino
Spedizione gratuita
star

98

QUALITÀ MASSIMA

VEDI SU AMAZON
Amazon.it
#2

  • CP2102 MICRO USB to UART TTL Module
  • CP2102 Driver Download Link: http://www.silabs.com/products/mcu/pages/usbtouartbridgevcpdrivers.aspx
  • With a resettable fuse. In the event of accidental short-circuit can effectively protect your device and computer USB port to download
  • With DTR trigger signal output can be directly arduino pro mini ATMEGA328P and other Arduino board download traffic.
  • 12,99 € SU AMAZON
SEENGREAT
SEENGREAT
SeenGreat PL2303 USB to TTL UART Serial Port Module for Windows Linux MAC OS Fits Raspberry Pi 5 Adopts PL2303GS Chip Type-C Connector UART TTL level Switch 3.3V/5V Logic Level
Spedizione gratuita
star

96

QUALITÀ SUPERIORE

VEDI SU AMAZON
Amazon.it
#3

  • This usb to uart module (SG-C2303-01C) is a high-performance USB-to-serial port module, adopts PL2303GS chip, supports USB 2.0 standard, which can realize fast and reliable data transmission and ensure efficient communication performance
  • The PL2303 USB to UART (TTL) Serial Port Module offers a variety of configuration options, including the setting of parameters such as baud rate, data bits, stop bits, parity bits, etc., meeting the requirements of different serial devices
  • The usb to ttl module is added rich flow control functions, such as hardware flow control (RTS/CTS) and software flow control (XON/XOFF), which can achieve more reliable data transmission and communication control
  • This usb to uart module is added the indicators of power supply, TXD, RXD , used to indicate the use status, and UART TTL level switching switch, which can be switched between 3.3V/5V conveniently and quickly. The hardware flow control pins CTS and RTS are derived to meet more applications
  • The PL2303 serial port module is suitable for a variety of operating systems, including Windows, Linux and Mac OS, and can be seamlessly connected with various mainstream computers and devices to provide stable and reliable serial communication; no need for additional drivers, just plug the module into the USB connector of the computer, it can be automatically recognized and started to use. It has the characteristics of plug and play, convenient and fast
  • 11,25 € SU AMAZON
SEENGREAT
SEENGREAT
SeenGreat FT232 USB TO UART TTL Communication Module for Windows Linux MAC OS FT232 USB C Converter Module Onboard FT232RL Power Supply TXD RXD Indicators 3.3V 5V Logic Level
Spedizione gratuita
star

92

QUALITÀ OTTIMA

VEDI SU AMAZON
Amazon.it
#4

  • This FT232 USB to TTL serial converter adapter(SG-C232-01C) is adopts FT232RL chip, and electronic components, supporting USB 2.0 standardwhich features marvellous reliability and stability, and can work stably for a long time
  • This usb to uart module provides an easy-to-use serial port communication interface. Users only need to plug it into the USB port of the computer to transmit data through the serial port
  • The usb to ttl module is added UART TTL level switching switch, which can be switched between 3.3V/5V conveniently and quickly, and the indicators of power supply, TXD, RXD , which are used to indicate the use status
  • The hardware flow control pins CTS and RTS are derived to meet more applications
  • This ft232 usb uart module is compatible with multiple operating systems and development platforms, including for Windows, Mac OS X, Linux, etc., and also supports multiple development languages, such as C, C++, Python, etc.
  • 12,99 € SU AMAZON
HiLetgo
HiLetgo
HiLetgo 5pcs Ttl to RS485 485 to Serial UART Level Reciprocal Hardware Automatic Flow Control UART to RS485 Converter RS485 to Ttl
Spedizione gratuita
star

86

QUALITÀ AFFIDABILE

VEDI SU AMAZON
Amazon.it
#5

  • TTL to RS485 485 to Serial UART Adapter
  • Compatible with 3.3V and 5.0V power supply.
  • Has RXD, TXD signal indicator light, monitor send and receive status.
  • Support multi-machine communication, allowing access at up to 128 devices on the bus
  • The module can be hot swapped, the signal does not appear dead phenomenon.
  • 9,99 € SU AMAZON
ARCELI
ARCELI
ARCELI 5 pezzi MAX3232 - Modulo di collegamento a presa TTL seriale a scheda convertitore TTL DB9 adatto per aggiornamenti di attrezzature come DVD
Spedizione gratuita
star

81

QUALITÀ BUONA

VEDI SU AMAZON
Amazon.it
#6

  • Utilizza la porta seriale DB9, esegui TX, RX, VCC, GND, comodo da collegare al cavo dupont.
  • Tensione di esercizio: 3,3 V-5,5 V, livello logico RX/TX equivalente alla potenza VCC.
  • Può essere utilizzato per programmare STC SCM, STM32 SCM, NXP SCM, Renesas SCM, NEC SCM.
  • Ampiamente usato per riabilitazione radio, mobile Root, XBOX360 Root, GPS, test e riparazione di veicoli, DVD Root, riparazione hard disk, kit top box, ecc.
  • Adatto per tutti i tipi di comunicazione seriale DB9 a TTL necessaria per situazioni o progetti elettronici.
  • 8,99 € SU AMAZON
TECNOIOT
TECNOIOT
TECNOIOT 5pcs Cp2102 USB 2.0 to UART TTL 5pin Module Serial Converter + Cable
Spedizione gratuita
star

81

QUALITÀ BUONA

VEDI SU AMAZON
Amazon.it
#7

  • 【CP2102TTL】The main chip CP2102, generate a virtual serial port after installing the driver.The USB to serial port can be used STC-ISPV3.94 above download old versions STC microcontroller that STC89C (LE) and STC12C (LE) Series.
  • 【Compatible】USB to take power , leads to the interface includes 3.3V(<40mA),5V, GND, TX, RX, the signal pin level is 3.3V, positive logic.Onboard status indicator lights transceiver , install the correct drivers status indicator lit, when the communication transceiver indicator flashes , the higher the intensity , the lower the baud rate.
  • 【Easy operation】Download STC microcontroller steps:TXD connected microcontroller RXD, RXD connected MCU TXD, GND connected to GND, 5V connected to VCC, points to download the software , and then provide the above said four feet into the microcontroller.
  • 【Compatible】support for the operating system : windows vista / xp / server 2003/200, Mac OS-X/OS-9, Linux
  • 【Note】 The MCU must have basic working conditions, including power, reset and clock ! While MCU TXD, RXD not followed by other peripheral devices, including the MAX232 and do not pick , otherwise it will lead to Download failed ! ! In the meantime , please do not disconnect the module from the computer !
  • 17,01 € SU AMAZON
Waveshare
Waveshare
Waveshare USB to CAN Adapter Analyzer, Adopts STM32 Chip Scheme, 4 Working Modes, Stable Communication, for Windows XP/7/8/10/11, for Raspberry Pi OS/Jetson Nano Ubuntu and Other Linux System
Spedizione gratuita
star

76

QUALITÀ BUONA

VEDI SU AMAZON
Amazon.it
#8

  • The data of CAN bus can be collected to the PC via USB to realize the receiving and transmitting control, data analysis, collection and monitoring of the CAN Bus Network
  • Support CAN2.0A (standard frame) and CAN2.0B (extended frame). Support CAN communication baud rate range: 5kbps~1Mbps, can customize CAN baud rate. Support multiple CAN data receiving methods: it can be configured to receive only the data with the specified ID, or specify the ID to automatically respond to the configured data
  • Supports 4 Working Modes: normal mode, loopback mode, silent mode, and silent loopback mode. Support multiple CAN data Transmission Modes: single frame transmission, multi frame transmission, manual transmission, timed transmission and cyclic transmission
  • Adopts the Original STM32F103 Chip, more stable and reliable communication. Support to set the communication baud rate of USB virtual COM port (9600~2000000bps), the default is 2000000bps
  • Supports Windows XP/7/8/10/11, Compatible with Raspberry Pi OS/Jetson Nano Ubuntu and other Linux Systems, Supports Secondary Development(Just deal with the receiving and sending commands)
  • 29,99 € SU AMAZON
IbdrY
IbdrY
IbdrY Accessori BMS Ufficiali Daly Toccare LCD Display, Modulo Bluetooth, USB Can Bus/UART/RS485, Sensori NTC, Power Board,RS485 to USB Cable
star

75

QUALITÀ BUONA

VEDI SU AMAZON
Amazon.it
#9

  • Modulo Canbus : Lo strumento di trasmissione dei dati tra il PC e la Mustensure BMS che l'unità è installata normalmente e la sequenza di linea corretta per comunicare normalmente la distanza di trasmissione 250kbs , velocità di trasmissione veloce , anti-interferenza forte 500kbs.
  • 3in Screen RS485Port: connettore plug-in, nessuna saldatura richiesta.Cablaggio con clip pop-up, facile da installare.Chell di isolamento chiuso, protezione multipla, anti-statico, anti-stetico.L'ampia temperatura va da -20 ℃ a 70 ℃, consumo di energia inferiore a 20 mA, consumo di energia del sonno fino a 0,1 W.Display accurato di.
  • Modulo Bluetooth : Controllare le informazioni delle batterie attraverso la connessione Bluetooth con il telefono cellulare, è conveniente per i clienti per gestire le batterie e fornire intellent, efficienti, veloci e sicure utilizzando l'ambiente.
  • Schermata LCD Toucheble: l'interfaccia predefinita per TOucheble LCD per connettersi con BMS è UART. Ma può anche supportare la comunicazione RS485 (OEM).PLS presta attenzione quando BMS utilizza la comunicazione UART di LCD, non può collegare GPS o BT contemporaneamente.I PLS non inseriscono l'interfaccia errata per Avoide BMS danneggiato.
  • NTC (controllo della temperatura termica): confermare che la versione del BMS prima del cablaggio, deve prima collegare l'NTC sul BMS, altrimenti il BMS attiverà protezione se rileva la temperatura anormale., non posizionare a piacimento.
  • 34,17 € SU AMAZON
TECNOIOT
TECNOIOT
TECNOIOT 4pin PL2303 USB to UART TTL Cable Module RS232 Serial 4-pin PL2303HX Cable
Spedizione gratuita
star

65

QUALITÀ BUONA

VEDI SU AMAZON
Amazon.it
#10

  • 【FTDI 4PIN】 USB TO RS232 TTL PL2303HX ADATTATORE MODULO CONVERTITORE AUTOMATICO 5V USCITA, FORNISCE IL MODO MIGLIORE E COMODO PER COLLEGARE I DISPOSITIVI TTL RS232 O DEMO BRD. AL TUO COMPUTER, TRAMITE LA PORTA USB.
  • 【Design compatto】 Chip TTL COM PC-PL2303HX integrato; Connettore USB standard tipo A maschio e TTL a 4 pin; Lunghezza del cavo: 100 cm (39 3/8 in)
  • 【COMPATABILITÀ】 Un modo semplice e semplice per fornire supporto USB ai tuoi progetti; Disponibile per Linux, Mac, WinCE e Windows (XP, 2003), Vista, Win 7
  • 【Metodo di collegamento】 ripetizione Il pennello necessita solo di tre linee, utilizzate nelle tre linee di segnale RX TX GND, il VCC senza accesso. L'amica dell'ago 4,5 sopra, non collegata all'ago VCC e BT. Usa RXD collegato alla scheda target TX, TXD e target board RX, GND collegato a GND se non, RX e TX swap.
  • ➮║Driver for Win7 / 10: http://www.totalcardiagnostics.com/support/Knowledgebase/Article/View/92/20/prolific-usb-to-serial-fix-official-solution-to-code-10-error ➮║or here: http://www.prolific.com.tw/US/ShowProduct.aspx?p_id=225&pcid=41 ➮║Driver installation guide (you can also find the download link here): http://www.instructables.com/id/Usb-to-SerialTTL-adapter/
  • 8,16 € SU AMAZON
uart to usb usb to uart uart to rs485